Exercise Profile
  • Target Muscle Group
  • Exercise TypeStrength
  • Equipment RequiredMachine
  • MechanicsCompound
  • Force TypePush
  • Experience LevelBeginner
  • Secondary Muscles
    Shoulders, Triceps
Target Muscle Group


Chest Muscle Anatomy Diagram

Decline Smith Machine Bench Press Overview

The smith machine decline bench press is a variation of the decline bench press and is used to target muscles of the chest.

The smith machine decline bench press eliminates some of the need for shoulder stability during the exercise, allowing the lifter to better isolate the chest muscles. The angle used during the decline smith machine bench press also allows one to target the lower portion of the chest.

Decline Smith Machine Bench Press Instructions

  1. Lie flat on an decline bench inside the smith machine and set your hands just outside of shoulder width.
  2. Set your shoulder blades by pinching them together and driving them into the bench.
  3. Take a deep breath and unrack the weight by rotating the bar off the safety pins while maintaining tightness through your upper back.
  4. Inhale and allow the bar to descend slowly by unlocking the elbows.
  5. Lower the bar in a straight line to the base of the sternum (breastbone) and touch the chest.
  6. Push the bar back up in a straight line by pressing yourself into the bench, driving your feet into the floor for leg drive, and extending the elbows.
  7. Repeat for the desired number of repetitions.

Decline Smith Machine Bench Press Tips

  1. Technique first, weight second - no one cares how much you bench if you get injured.
  2. Keep the bar in line with your wrist and elbows and ensure it travels in a straight line. To keep the wrist straight, try to position the bar as low in the palm as possible while still being able to wrap the thumb.
  3. If you want to keep more tension through the triceps and chest, stop each repetition just short of lockout at the top.
  4. Don’t worry about tucking the elbows excessively, much of this advice is from geared lifters using suits. A slight tuck on the way down may be advisable for some lifters but other lifters can use an excellent cue from Greg Nuckols that accomplishes the same thing: “Flare and push”.
  5. Arching may be advisable depending upon your goals but ensure that most of the arch comes from the mid to upper back and not your lower back. If your lower back is cramping as you set up for the lift, you’re out of position and putting yourself at risk for potential injury.
  6. The bar should touch your chest with every single repetition. If you want to overload specific ranges of motion, look into board presses or accommodating resistance with chains or bands.
  7. As the bar descends, aim for your sternum (breastbone) or slightly below depending upon the length of your upper arm in order to promote a linear bar path.
  8. Intermediate and advanced lifters may use a thumbless or “suicide” grip but for the majority of lifters, it would be wiser to learn how to bench with the thumb wrapped around the bar at first.
  9. Fight the urge to allow the wrists to roll back into extension, think about rolling your knuckles toward the ceiling.
  10. Experiment with grip width - if you have longer arms you may need to use a slightly wider grip. However, if you’re feeling pressure in the front of the shoulder during the exercise, you may need to widen your grip, improve scapular retraction, or slightly lessen the range of motion via exercises such as floor or board presses.
  11. Squeeze the bar as tightly as possible to help enhance shoulder stability.
  12. Ensure the shoulder blades remain retracted and don’t allow them to change position as you press.
  13. The bar should descend under control and touch the lifter’s chest - no bouncing or excess momentum.
  14. Think about trying to push yourself away from the bar instead of pushing the bar off of you.
  15. Tightness through the upper back should be one of your main priorities throughout the course of the lift.
  16. Ideally, use a spotter to help assist with the lift off in order to maintain tension through the upper back.
  17. Focus on pulling the bar apart or trying to “bend the bar” to activate some of the intrinsic stabilizers in the shoulder.
  18. The glutes and shoulder blades should maintain contact with the bench throughout the entirety of the movement.
Posted on: Mon, 02/24/2014 - 10:49

Not the best chest exercise but a great alternative for when you haven't got someone to hand weights to you when going heavy on the decline dumbell press.

My chest workout: incline DB press, decline press, DIps, flat DB flyes

To burn off sometimes I add 2 or 3 sets of machine press.

Posted on: Sun, 08/11/2013 - 10:38

brilliant for the chest.as dorian yates say,s a must to do.works the pec,s really hard

Posted on: Fri, 05/04/2012 - 12:50

this is very helpfull , the best sight i,ve ever found.